Temperatur von F auf C umstellen RN09
Moderator: Forumsteam
-
- Rookie
- Beiträge: 15
- Registriert: 13. Mai 2018, 00:58
- Meine R1: RN 09, BJ: 2003
Temperatur von F auf C umstellen RN09
Hallo,
ich möchte bei meiner R1 RN09 die Temperatur von F auf C umstellen. Weiß jemand wie das geht?
ich möchte bei meiner R1 RN09 die Temperatur von F auf C umstellen. Weiß jemand wie das geht?
- PEB
- zwanglos ranglos
- Beiträge: 24425
- Registriert: 18. August 2003, 19:54
- Meine R1: R1M
- Extras: ...
- Wohnort: Zuhause
- Hat sich bedankt: 811 Mal
- Danksagung erhalten: 808 Mal
Re: Temperatur von F auf C umstellen RN09
Ist das ein deutsches Modell?
Wenn es ein amerikanisches ist, dann geht das nicht.
Wenn es ein amerikanisches ist, dann geht das nicht.
-
- Rookie
- Beiträge: 15
- Registriert: 13. Mai 2018, 00:58
- Meine R1: RN 09, BJ: 2003
- PEB
- zwanglos ranglos
- Beiträge: 24425
- Registriert: 18. August 2003, 19:54
- Meine R1: R1M
- Extras: ...
- Wohnort: Zuhause
- Hat sich bedankt: 811 Mal
- Danksagung erhalten: 808 Mal
Re: Temperatur von F auf C umstellen RN09
Wie beginnt die Fahrgestellnummer auf dem Rahmen?
Steht da YRN09..., wird es zumindest eine europäische sein.
Ich weiß nicht wie die amerikanischen Modelle der RN09 heißen.
Steht da YRN09..., wird es zumindest eine europäische sein.
Ich weiß nicht wie die amerikanischen Modelle der RN09 heißen.
- SLIDER-S
- *Rat der 17*
- Beiträge: 10490
- Registriert: 12. September 2005, 15:18
- Meine R1: R1M..2016
- Wohnort: 67346 Speyer
- Hat sich bedankt: 3 Mal
- Danksagung erhalten: 121 Mal
Re: Temperatur von F auf C umstellen RN09
Poste mal den Anfang der Rahmen-Nr. , sollte JYARN 091 für Modell 2002 oder 095 für 2003 sein.Gunitmember hat geschrieben:Wie finde ich heraus ob es ein dt. Modell ist?
Hast noch Lichtschalter am rechten Stummel (2002) oder Warnblinker am linken Stummel (2003).
Die US-Modelle der RN09 sind nach meiner Kenntnis die RN10.
-
- Rookie
- Beiträge: 15
- Registriert: 13. Mai 2018, 00:58
- Meine R1: RN 09, BJ: 2003
Re: Temperatur von F auf C umstellen RN09
Habe Warnblinkerschalter links der aber nicht funktioniert. Rahmennr. ist JYARN095
- SLIDER-S
- *Rat der 17*
- Beiträge: 10490
- Registriert: 12. September 2005, 15:18
- Meine R1: R1M..2016
- Wohnort: 67346 Speyer
- Hat sich bedankt: 3 Mal
- Danksagung erhalten: 121 Mal
Re: Temperatur von F auf C umstellen RN09
Dann sollte das ein EU bzw. Deutsches Modell von 2003 sein.Gunitmember hat geschrieben:Habe Warnblinkerschalter links der aber nicht funktioniert. Rahmennr. ist JYARN095
Evtl wurde mal das Cockpit wegen Defekt getauscht, die Geschwindigkeit ist in Km/h oder Mp/h
- PEB
- zwanglos ranglos
- Beiträge: 24425
- Registriert: 18. August 2003, 19:54
- Meine R1: R1M
- Extras: ...
- Wohnort: Zuhause
- Hat sich bedankt: 811 Mal
- Danksagung erhalten: 808 Mal
Re: Temperatur von F auf C umstellen RN09
Es gab doch mal auf der Yamaha-Seite die Benutzerhandbücher für die Mopeds zum Runterladen.
Da sollte drinstehen, wie man die Einheit umstellt von °F nach °C. Leider finde ich den Link nicht mehr.
Da sollte drinstehen, wie man die Einheit umstellt von °F nach °C. Leider finde ich den Link nicht mehr.
-
- Rookie
- Beiträge: 15
- Registriert: 13. Mai 2018, 00:58
- Meine R1: RN 09, BJ: 2003
Re: Temperatur von F auf C umstellen RN09
Geschwindigkeit kann ich in kmh oder mph anzeigen lassen aber die Temperatur bleibt immer auf F.
- SLIDER-S
- *Rat der 17*
- Beiträge: 10490
- Registriert: 12. September 2005, 15:18
- Meine R1: R1M..2016
- Wohnort: 67346 Speyer
- Hat sich bedankt: 3 Mal
- Danksagung erhalten: 121 Mal
Re: Temperatur von F auf C umstellen RN09
Hab die Bedienanlaitung meiner RN091 noch und grad mal geschaut, Tacho lässt sich wie schon gesagt umstellen.
Von der Temperaturanzeige steht nix drin von Umstellen
Von der Temperaturanzeige steht nix drin von Umstellen
-
- Rookie
- Beiträge: 15
- Registriert: 13. Mai 2018, 00:58
- Meine R1: RN 09, BJ: 2003
Re: Temperatur von F auf C umstellen RN09
Hat jemand zufällig eine Bedienungsanleitung als PDF oder so?
-
- Rookie
- Beiträge: 15
- Registriert: 13. Mai 2018, 00:58
- Meine R1: RN 09, BJ: 2003
Re: Temperatur von F auf C umstellen RN09
Hab das noch gefunden und komme auch ins diag aber wenn ich den Killswitch drücke passiert nichts.
To switch the water temperature display units:
1. Set the engine kill switch to OFF/STOP.
2. Hold the “RESET” and “SELECT” buttons down then turn the key to the on position (keep holding the reset and select buttons until “Co” appears in the left of the display area instead of the distance and time).
3. Press the “SELECT” button. The display changes to “dIAG “.
4. Press both the “RESET” and “SELECT” buttons at the same time.
“d01: xx” appears in the display area. (your TPS value is displayed in “xx”, it is unimportant for this change.)
5. Pressing the “RESET” button 2 times displays “d62: xx”.
The “xx” in “d62: xx” indicates which thermometric scale to display, Celsius or Fahrenheit.
“00” = No display
“01” = Celsius (°C)
“02” = Fahrenheit (°F)
To change the display, operate the engine kill switch from “OFF” to “ON”. The thermometric
indication changes in order of “00”, “01”, “02”, and back to “00” and so on (each time the kill switch it turned off and on again).
5. When the desired setting appears, turn the key to the off position to store the new setting.
On some R6 and R1 bikes, switching the kill switch on and off refuses to change the number in D62 and you have to ground a "service" wire on the ECU. On my 08 R6 it was ECU wire #16 (light green with gold bands), you cut it where it comes out of the ecu connector, and ground the ecu side (to the battery works well). After doing this modification, to change the D62 numbers you have to hold select and reset for more than 20 seconds, if cycling the kill switch doesn't change it.
To switch the water temperature display units:
1. Set the engine kill switch to OFF/STOP.
2. Hold the “RESET” and “SELECT” buttons down then turn the key to the on position (keep holding the reset and select buttons until “Co” appears in the left of the display area instead of the distance and time).
3. Press the “SELECT” button. The display changes to “dIAG “.
4. Press both the “RESET” and “SELECT” buttons at the same time.
“d01: xx” appears in the display area. (your TPS value is displayed in “xx”, it is unimportant for this change.)
5. Pressing the “RESET” button 2 times displays “d62: xx”.
The “xx” in “d62: xx” indicates which thermometric scale to display, Celsius or Fahrenheit.
“00” = No display
“01” = Celsius (°C)
“02” = Fahrenheit (°F)
To change the display, operate the engine kill switch from “OFF” to “ON”. The thermometric
indication changes in order of “00”, “01”, “02”, and back to “00” and so on (each time the kill switch it turned off and on again).
5. When the desired setting appears, turn the key to the off position to store the new setting.
On some R6 and R1 bikes, switching the kill switch on and off refuses to change the number in D62 and you have to ground a "service" wire on the ECU. On my 08 R6 it was ECU wire #16 (light green with gold bands), you cut it where it comes out of the ecu connector, and ground the ecu side (to the battery works well). After doing this modification, to change the D62 numbers you have to hold select and reset for more than 20 seconds, if cycling the kill switch doesn't change it.